PTFE Coated Fiberglass Mesh Conveyor Belt
Four Tie Bar Ebm Machine,High Speed Blow Moulding Machine,Pe Blow Molding Machine,Automatic Pe Blow Bottle Machine Spe Machine , https://www.spemachine.com
1. PTFE Mesh Conveyor Belt
2. Heat resistant, Microwave safe
3. High drying efficiency
4. Non-toxic & non-stick
5. Great tensile strength
PTFE Coated Fiberglass Mesh Conveyor Belt
PTFE Coated Fiberglass Mesh Conveyor Belt is ideally suited for conveying products within highly efficient air distribution systems allowing optimised moisture removal to take place and is commonly used within ultra violet and infra red dryer units
The open area allows maximum air flow optimising drying times whilst its extreme properties make it a natural choice for dryer manufactures.
Applications
PTFE Coated Fiberglass Mesh Conveyor Belts are used in applications such as the drying of printed products for example; Point of display stands, T-shirts, glass and mass produced paper prints. Print dryers usually opt for Ultra violet, Infra red or hot air as the heat source to dry.
Other applications range from the drying of cereals, non woven's, charcoal interlinings, carpet & carpet tiles, printed circuit boards and shrink-wrap tunnels but to name a few.
Features & Benefits
PTFE open mesh conveyor belting is light weight and cost effective therefore is easy to handle and less expensive than wire alternatives that can be difficult to replace. Often supplied with a metallic clipper type fastener these style of belts can easily be removed and replaced therefore minimising downtime and saving money. This material can be offered in carbon loaded black therefore providing antistatic properties.
Material Properties
· Temperature resistance: -70° C up to plus 260° C
· Chemical Inertness
· Ultraviolet, Infra-red, microwave, radio frequency resistance
· Non-Stick surface
· Lightweight and energy efficiency for economical operation
Additional Information
4x4 open area mesh is available in widths up to 4000mm wide and can be supplied at any length required. In addition film, glass or kevlar can be applied as edge reinforcement depending of the environment it will be used within. There are various methods of joining screen-printing belts however the metallic clipper or spiral types are more typical
Model
Mesh Size
Material
Thickness
Weight
Temp Resistance
Max Width
Tensile Strength
YS-6001
1x1mm
 fiberglass
0.5mm
370g/m²
-70-320C
4000mm
310/290N/cm
YS-6002
2x2mm
fiberglass
0.7mm
450g/m²
-70-320C
4000mm
350/310N/cm
YS-6003
4x4mm
fiberglass
1.0mm
400g/m²
-70-320C
4000mm
390/320N/cm
YS-6004
4x4mm
fiberglass
1.0mm
450g/m²
-70-320C
4000mm
390/320N/cm
YS-6007
4x4mm
fiberglass
+kevlar1.2mm
600g/m²
-70-320C
4000mm
895/370N/cm
YS-6008
4x4mm
fiberglass
1.0mm
500g/m²
-70-320C
4000mm
395/370N/cm
YS-6010
4x4mm
Kevlar
1.0mm
500g/m²
-70-320C
4000mm
900/600N/cm
YS-6012
4x4mm
fiberglass
1.0mm
550g/m²
-70-320C
4000mm
395/370N/cm
YS-6013
10x10mm
fiberglass
1.2mm
450g/m²
-70-320C
4000mm
360/300N/cm
YS-6014
0.5x1mm
fiberglass
0.5mm
420g/m²
-70-320C
4000mm
310/290N/cm
YS-6015
2x2.5mm
fiberglass
0.9mm
600g/m²
-70-320C
3000mm
390/320N/cm