Slip Ring for Center Pivot Irrigation System, Collector Ring

Model NO.: 1404001
Ground Drainage and Irrigation Machinery Type: Pumping Irrigation
Certification: ISO9001:2008, CCC
Condition: New
Application Field: Agriculture
Trademark: IRRITECH
Origin: China
Model NO.: 1404001
Ground Drainage and Irrigation Machinery Type: Pumping Irrigation
Certification: ISO9001:2008, CCC
Condition: New
Application Field: Agriculture
Trademark: IRRITECH
Origin: China

COLLECTOR RING-ELECTRIC CONTROL FOR CENTER PIVOT IRRIGATION SYSTEM

Model No.: 1404001

Working temperature:

Temperature: -20ºC~60ºC

Relative humidity:<95%

Specification:

1.Dynamic contact resistance:<10mΩ

2.Voltage:0-480V/240VAC

3.Current:@25Amp per ring

4.Contact material:brass & Carbon brush

5.House material:metal base & ABS cover/aluminium cover

Feature:

1.with 11 rings the collector ring gives total connection between the main electric panel and the spans

2.Bearing rotate,make sure good performance.

3.the collector ring is water proofed

4.Stainless steel shaft makes long lifetime.

Installation:

The collector ring is installed on the center pivot irrigation frame,consists of rotation part and fixation part.The rotatry structure of rotating prt connected device called "roter:,the fixed part installed on the bracket of the equipment,called "stator"

The "rotar" is fixed through the G1" threaded hole or the G 1/2" threaded hole on the base side.The "stator" is installed on the base through the mouting shaft G1"

The span cable must be allowed to swivel at the pivot, otherwise it would be wrap itself around the pivot. The device which allows the cable to rotate is called a collector ring.
The collector ring consists of brass rings in a stack that remain stationary and are separated by insulators. Contact brushes revolve around the brass rings providing continuous flow of current without twisting the cable as the machine makes revolutions around the field.
The electrical control calbe is then fed from the collector ring through a pipe which is J-shaped and exist the riser near the top of the riser. The control cable is then routed down the pivot leg along the pivot brace, and into the main control panel.

Mounts on a stainless steel J-Pipe above the upper elbow to
minimize water contact.
Sealed to prevent water and dust contamination inside.
Positioning the collector ring above the upper elbow ensures that
the brushes are always aligned with the slip rings - no side forces.
Small diameter means less brush wear and longer trouble-free life.
Easy to replace / repair, if needed. Electronic positioning resolver is positively attached and protected
from the elements.
Mechanical controls are easy to adjust.
The same collector ring is used on all pivot points from 6 5/8"
through 10".
The collector ring transfers the incoming 480-volt power to the rotating spans. The 480-volt power is supplied to nonrotating copper rings (one for each conductor). Brushes (one for each conductor) rotate with the spans. The brushes transfer the 480-volt power from the copper rings to the span wire.


Slip Ring for Center Pivot Irrigation System, Collector Ring
A series of synchronous motors and asynchronous motors, which are widely used in the industrial sector, and most of which operate under various harsh conditions, are widely used in the industrial sector.

Slip Ring for Center Pivot Irrigation System, Collector Ring

COLLECTOR RING-ELECTRIC CONTROL FOR CENTER PIVOT IRRIGATION SYSTEM

Model No.: 1404001

Working temperature:

Temperature: -20ºC~60ºC

Relative humidity:<95%

Specification:

1.Dynamic contact resistance:<10mΩ

2.Voltage:0-480V/240VAC

3.Current:@25Amp per ring

4.Contact material:brass & Carbon brush

5.House material:metal base & ABS cover/aluminium cover

Feature:

1.with 11 rings the collector ring gives total connection between the main electric panel and the spans

2.Bearing rotate,make sure good performance.

3.the collector ring is water proofed

4.Stainless steel shaft makes long lifetime.

Installation:

The collector ring is installed on the center pivot irrigation frame,consists of rotation part and fixation part.The rotatry structure of rotating prt connected device called "roter:,the fixed part installed on the bracket of the equipment,called "stator"

The "rotar" is fixed through the G1" threaded hole or the G 1/2" threaded hole on the base side.The "stator" is installed on the base through the mouting shaft G1"

The span cable must be allowed to swivel at the pivot, otherwise it would be wrap itself around the pivot. The device which allows the cable to rotate is called a collector ring.
The collector ring consists of brass rings in a stack that remain stationary and are separated by insulators. Contact brushes revolve around the brass rings providing continuous flow of current without twisting the cable as the machine makes revolutions around the field.
The electrical control calbe is then fed from the collector ring through a pipe which is J-shaped and exist the riser near the top of the riser. The control cable is then routed down the pivot leg along the pivot brace, and into the main control panel.

Mounts on a stainless steel J-Pipe above the upper elbow to
minimize water contact.
Sealed to prevent water and dust contamination inside.
Positioning the collector ring above the upper elbow ensures that
the brushes are always aligned with the slip rings - no side forces.
Small diameter means less brush wear and longer trouble-free life.
Easy to replace / repair, if needed. Electronic positioning resolver is positively attached and protected
from the elements.
Mechanical controls are easy to adjust.
The same collector ring is used on all pivot points from 6 5/8"
through 10".
The collector ring transfers the incoming 480-volt power to the rotating spans. The 480-volt power is supplied to nonrotating copper rings (one for each conductor). Brushes (one for each conductor) rotate with the spans. The brushes transfer the 480-volt power from the copper rings to the span wire.


Slip Ring for Center Pivot Irrigation System, Collector Ring
A series of synchronous motors and asynchronous motors, which are widely used in the industrial sector, and most of which operate under various harsh conditions, are widely used in the industrial sector.

Slip Ring for Center Pivot Irrigation System, Collector Ring

Fork Extension

Fork Extension,Fork Arm Extension,Forklift Fork Extensions,Heavy Duty Fork Extensions

Shandong Techence Forging Co.,Ltd , https://www.shandongtechence.com