Solar Bore Water Pump Price, Solar Powered Borehole Water Pump Price 1HP 1.5HP
Medical titanium products are a class of high-performance materials and devices used in a wide range of medical applications that are manufactured from highly pure titanium. These products are prized for their unique performance characteristics, including excellent biocompatibility, which allows them to work seamlessly with human tissue in a variety of medical applications, reducing the risk of rejection for patients. In addition, medical titanium products are lightweight and high-strength, making them the first choice for the manufacture of lightweight yet robust medical devices such as artificial joints, dental implants and surgical tools. Its excellent corrosion resistance ensures that these products maintain their integrity in the body over time, meeting the need for long-term reliability of implantable medical devices. Medical titanium products also excel in the field of medical imaging, where their high transparency to ultrasound is critical for sonography and medical ultrasound imaging. In addition, they are able to withstand autoclaving and sterilization processes, ensuring the sterility of the device. In short, medical titanium products play an integral role in modern healthcare, making a significant contribution to improving patient outcomes, surgical safety and the performance of medical devices.
Medical Titanium,Medical Grade Titanium,Medical Titanium Bar,Medical Titanium Plate Yesino Metal Co., Ltd , https://www.yesinometal.com
3 Year for motor and controller. Solar panel 20 years(Optional)
Â
Installation
 1. Wiring the pump
 Connecting a longer cable to the pump,(size of cable must be at least 1.5mm²)
Use the parts contained in the cable connector kit( heat-shrink tube and tape) to connect a longer supply wire to the pump. If you don't have a heat gun to shrink the tube, the barrel of your soldering iron will do or you can use a butane torch but with great care so you don't melt the insulation or set it on fire. Bare the insulation back as shown above.
A. Layout the components needed to make the joinÂ
B. Put the large diameter piece of heat-shrink over the main cable and then the smaller diameter pieces over the individual wires, keep the heat-shrink back away from the joints as you solder them. Any heat transfer will prematurely shrink the heat-shrink.
C.  Slide the small heat-shrink over the soldered joints and heat using a heat gun or alternative heat source to shrink the sleeve down over the wires.
D. Wrap the tape over the sealed joints
E. Finally slide the large diameter heat-shrink over the completed joint and shrink to it.
Place the pump in water before you start wiring the controller box this will allow the pump to go through the pre-conditioning required. Do not put the pump in its final position until you have tested it, unless it is easy to see and remove.
Â
  A. Low-voltage protection (it is automatic)
  B. over-current protection( it is automatic)
  C. protection for low water level in well( A B sensor)
  D. protection for full water level in tank( L H sensor)
  E. Controlling running speed of motor( speed regulator)
  F. Delay working when full water in tank( a timer inside can delay working for 30 seconds when the tank going to not full)
  G. MPPT function.(maximum power point tracking)
  H. Battery is optional.( battery can be used with solar charger battery system)
Â
Warranty:
3 Year for motor and controller. Solar panel 20 years(Optional)
Â
Installation
 1. Wiring the pump
 Connecting a longer cable to the pump,(size of cable must be at least 1.5mm²)
Use the parts contained in the cable connector kit( heat-shrink tube and tape) to connect a longer supply wire to the pump. If you don't have a heat gun to shrink the tube, the barrel of your soldering iron will do or you can use a butane torch but with great care so you don't melt the insulation or set it on fire. Bare the insulation back as shown above.
A. Layout the components needed to make the joinÂ
B. Put the large diameter piece of heat-shrink over the main cable and then the smaller diameter pieces over the individual wires, keep the heat-shrink back away from the joints as you solder them. Any heat transfer will prematurely shrink the heat-shrink.
C.  Slide the small heat-shrink over the soldered joints and heat using a heat gun or alternative heat source to shrink the sleeve down over the wires.
D. Wrap the tape over the sealed joints
E. Finally slide the large diameter heat-shrink over the completed joint and shrink to it.
Place the pump in water before you start wiring the controller box this will allow the pump to go through the pre-conditioning required. Do not put the pump in its final position until you have tested it, unless it is easy to see and remove.
Â
  A. Low-voltage protection (it is automatic)
  B. over-current protection( it is automatic)
  C. protection for low water level in well( A B sensor)
  D. protection for full water level in tank( L H sensor)
  E. Controlling running speed of motor( speed regulator)
  F. Delay working when full water in tank( a timer inside can delay working for 30 seconds when the tank going to not full)
  G. MPPT function.(maximum power point tracking)
  H. Battery is optional.( battery can be used with solar charger battery system)
Â