Cone crusher maintenance system
11.1 Regular inspection and maintenance Serial number Part content standard cycle Responsible for the job 1 Lubricate hydraulic lines and water seal dustproof devices 1. Pressure gauge oil flow and water flow and oil temperature 2. Cleaning oil and water pipelines to check oil pumps and valves and cylinders 3. Check the cleaning water seal device and dust ring 1. Normal indication, normal temperature 2. The pipeline is unblocked and the leaks are not working properly. 3. No leakage, no dust Every shift 30 to 45 days 30 to 45 days Operator fitter fitter 2 Body and spring part 1. Various screws 2. Various funnels 3. Spring and spring screws 1. Fit properly 2. Patching 3. Fastened, balanced, without break Every shift 30 to 45 days Every shift, 3 months to 1 year Operator fitter Operator fitter 3 Broken part 1. Compression nut tightening 2. Broken wall fastening 3. Moving cone part inspection 4. Check the tightness of the spherical bearing and the contact level of the contact surface 5. Check the matching clearance of each part 6. Rolling wall and fastening device 1. Fastened without looseness 2. No zinc and loose 3. The lower spherical surface is well fitted and the oil groove is unblocked. 4. Fastening, good contact, proper scraping, strengthening and sealing 5. The gaps in each department meet the standard 6. Replace the rolling wall or fasten Every shift 30 to 45 days 30 to 45 days 30 to 45 days 30 to 45 days Operator Operator fitter fitter fitter fitter 4 Drive shaft section Transmission gear 2. Transmission shaft bearing condition check 1. Meet the specified meshing clearance 2. Adjust to the specified clearance 30 to 45 days 30 days fitter fitter 5 Electrical part Motor temperature rise 2. Motor bearing 3. Short circuit ring and oil switch 4. All high and low voltage electrical systems 1. Not more than 60 ° C 2. Moderate clearance 3. Sensitive and reliable 4. Cleaning is sensitive and reliable Every shift One year 30 to 45 days 6 months Operator Electric fitter electrician electrician 11.2 Regular lubrication Serial number Lubricating part Lubrication method Type of lubricant Lubrication cycle Be responsible for Work type Come on Change oil 1 Vertical shaft, eccentric bushing, bevel gear, spherical bearing, drive shaft bearing Pressure cycle oil pressure 0.7~1.5kg/cm 2 45 #油油粘度 F50=5.24~7.07 The oil reaches the oil mark Change once every season Operator 2 Motor bearing Pressure pump Calcium sodium grease Drop point T=120°C Oil injection once a month Change oil every six months Electric fitter 11.3 Regular cleaning Serial number Cleaning site Cleaning requirements cycle Responsible for the job 1 Lubrication system External lubrication of all lubrication systems after parking Every shift Operator 2 Various parts of the body 1. After parking, clean the surface of the machine 2. Keep the machine clean 3. External cleaning of electrical and electronic facilities Every shift Operator 3 Other ministries 1. Waste oil rags are placed in a certain place 2. Sprinkle water around the machine (be careful not to spill on electrical equipment) 3. Clean up the discharged waste oil and do not flow to the cement foundation. 4. The hydraulic system is prohibited from entering or entering dust to prevent oil emulsification or pressure drop. Every shift Operator Desktop laser machine
UT-1490/1610/1325/1318, etc.
<
Desktop Laser Machine,Desktop Laser Cutter,Desktop Laser Cutting Machine ,Desktop Laser Engraving Machine Shandong U-May CNC Technology Co., Ltd. , https://www.sesamecnc.com
UTECH Desktop Mini Laser Engraver is equipped with Texas 32 Bit DSP control system, there is a Flash memory on the mother board, you can download the work file to the machine via USB cable.
Mini Laser Engraver is most suitable and the preferred choice of equipments in industries such as advertisement, gifts, shoes, toys, and etc.
Desktop Laser Engraving Machine feature:
1. Adjustable Speed and Power, Smooth and Precise Engraving and Cutting
2. USB Interface
3. Air Assist, Remove heat and combustible gases from the cutting surface.
60W Air pump
4. Embedded Exhaust Fan, Easier intall, Safer transport.
40W exhaust fan, flow can be 5.27m³\Min.
5. Rotary Axis, Engrave any cylindrical object.
6. Aluminum table platform, Leave no chippings on working area.
7. LCD english Panel and DSP control system, easy to operate
8. Water Cooling and Protection System.
The tube will not work without water, to protect laser tube.
9. Advanced Red cross position. easy to identify laser position.
10. Emergency Stop Button.
11. Lift handle on side, easy to lift the machine.
12. Manual or Electircal up down table optional
13. Taiwan Imported Hiwin linear rail transmission
14. Laser focal length: 50.8mm
15. Limit switch on front door & laser tube cover, once open any cover, it will stop work.
16. Machine service life: 1000-1500H for laser tube, 3-5 years for machine body.
Available Industries:
Marble engraving , tombstone carving , stone engraving , advertisements , packing and printing , molding and art craft industries.
Customized model:
Model
UT-2030/3050/4060
Laser tube
Water cooling Co2 sealed glass
Control system
32 Bit DSP with Flash memory
Drive type
Stepper motor
Laser Power
50W/60W
Working Size (mm)
200*300/300*500/400*600
Adjust Table (mm)
200
Max speed
800 mm/s
Image form
Plt, Dxf, Bmp, Ai, Dst
Resolution
1000 DPI
Repeatability
0.01 mm
PC Interface
USB 3.0 and USB Disk
Power
110~240V/ 50~60Hz
Warranty
12 Months